Water leak or burst pipe? Call 07564 495989
No hot water in Nottinghamshire and Derbyshire, example photographExample
Start with the symptoms

No hot water? One tap or the whole house

No hot water? Is it one tap or the whole house? Then ring 07564 495989.

07564 495989
Across Nottinghamshire and DerbyshirePhotos welcome
STEP 1 OF 2

Tell us what
has happened.

Water still escaping? Ring first. Otherwise, tell us here.

What is the problem?
Right now

No hot water? Check this first.

  1. 01

    Leave covers and safety devices alone

    Do not open a gas appliance, immersion heater or pressurised cylinder. Do not bypass a safety control or repeatedly reset equipment that shows a fault.

  2. 02

    Write down the pattern

    Note which taps are affected, whether cold water flows and any visible error message. A photograph of an external label is enough; do not dismantle anything to obtain it.

  3. 03

    Use the correct emergency route

    If there is a suspected gas leak or another immediate danger, follow the appropriate emergency advice. A water-plumbing enquiry form is not the route for reporting a dangerous appliance.

  4. 04

    Ring us

    Postcode and what you can see.

    Call 07564 495989

Keep people away from wet electrics, dirty water and sagging ceilings. If anyone is in danger, call 999.

Understand the problem

One fitting and a whole-house fault need different questions

If hot water has stopped, note whether it affects one tap or the whole property and whether cold water still flows. Do not remove appliance covers or adjust unfamiliar controls. Call us and tell us what is happening. For a gas appliance or boiler fault, use a gas engineer.

No hot water describes a symptom rather than a single fault. One mixer tap running cold, several outlets losing flow and every hot tap failing can lead to different investigations. Think about what you have already observed without repeatedly running water or changing settings. Tell us whether water flows at normal strength, whether the issue is new and whether it followed work on a tap, valve or appliance.

The way water is heated also matters, but you do not need to diagnose the heating system yourself. A visible make or model label and an error message can be useful information for the appropriate engineer. Do not remove a cover to find them. Gas appliances, electrical heaters and pressurised hot-water equipment have safety requirements and must not be opened or repaired as a general household check.

When you call, we tell you straight whether it is a plumbing fault we fix or one for a gas or electrical engineer. Tell us if occupants rely on accessible washing facilities, if the property is rented or if a landlord manages the heating system.

No hot water detail, example photographExample

Hot water is absent at one outlet or throughout the property.

A hot tap has little flow while the cold tap behaves normally.

A sudden change follows a fitting replacement or supply interruption.

Water where it shouldn't be?

Ring us. A postcode and what you can see is enough.

Call 07564 495989
From the first call

A clear route
through the problem.

You know what is happening, what is agreed and what comes next.

01

Identify the affected outlets

We ask whether one fitting or the whole property is affected and whether the problem concerns temperature, flow or both. Recent changes can help establish the context.

02

Confirm the service boundary

We work out what the fault is likely to be. If it is a gas or electrical fault, we tell you so you can call the right engineer.

03

Agree an appropriate inspection

For pipework, valves and taps, we agree access and isolation with you. The inspection should focus on the symptoms rather than assume a particular part has failed.

04

Clarify follow-up and use

Record any isolation, further referral or repair recommendation. We tell you what is safe to use until it is fixed.

Choose how to get in touch

Water still escaping?
Pick up the phone.

07564 495989
Which one is you?

Pick the closest match.

Only one tap affected

Describe the tap type and whether both hot and cold sides flow. Mention recent work to that fitting and whether other hot outlets still work normally.

Several outlets affected

Give the overall pattern and the visible type of water-heating system if known. Call to establish the right service rather than selecting an appliance repair from assumption.

Rented or managed property

Contact the landlord or agent through the agreed repair route. Keep a record of the report and any needs that make the loss of hot water especially difficult.

When you ring

What happens
when you ring.

07564 495989

Tell us what you can see

No jargon. Where the water is, what has stopped working, your postcode.

We help you make it safe

Where your stopcock is, what to switch off, what to leave alone.

Send a photo if it helps

A quick picture on WhatsApp shows us the fitting before we arrive.

You know the plan

What we will do and how it is priced, before any work starts.

Still dripping?

One call. Straight answers.

07564 495989
Questions, answered

No hot water questions.

Water where it shouldn't be? Ring us.

Call 07564 495989
Does no hot water always mean the boiler has failed?
No. A problem may affect one fitting, the supply or the wider hot-water system. The symptoms alone do not identify the cause. If it is the boiler, you need a gas engineer. Tell us which taps are affected and we will tell you what it needs.
Can I keep resetting the equipment?
Do not repeatedly reset equipment that shows a fault or bypass any safety feature. Follow the manufacturer’s user instructions only where they are clear and safe. If an appliance seems unsafe, stop using it and call an engineer for that type of equipment.
What if the hot tap has no flow at all?
Tell us whether cold water is available and whether other hot taps also have no flow. Mention recent plumbing work or a supply interruption. Do not turn unfamiliar valves or dismantle a mixer to investigate; a description of the pattern is the right starting point.
Can you repair an immersion heater or unvented cylinder?
For a gas appliance or boiler fault, use a gas engineer. Call with the symptoms and we will tell you whether it is one for us. Do not remove electrical covers, operate unfamiliar cylinder valves or interfere with safety discharge pipework while waiting for an assessment.
Should I send a photograph of the appliance?
A photo of the outside, a visible label or a displayed fault can help identify the equipment for the relevant service provider. Do not open panels, stand on furniture or enter a cramped unsafe space to take it. Remove personal documents from the frame.
What should tenants tell their landlord?
Describe when the problem started, which outlets are affected and whether any other water facilities are usable. Mention vulnerable occupants or accessibility needs. Keep a copy of the report and agree who will arrange attendance and authorise costs before booking privately.
Why is there no hot water when the heating works?
If the radiators are warm but the taps run cold, the fault is usually in how hot water is sent to the taps rather than in the heat source itself. A diverter or zone valve, a timer setting or a cylinder control are common culprits. Tell us what type of system you have when you call.
A clear next step

Plumbing emergency?
Ring us now.

Tell us your postcode and what is happening.

07564 495989
Call nowWhatsApp
STEP 1 OF 2

Tell us what
has happened.

Water still escaping? Ring first. Otherwise, tell us here.

What is the problem?
Plumbing photograph